Computerized accurate tape tension controller.
As the device always adjust tape feeding amount to be right tension on tape while measuring actual tension, accurate finish can be obtained.
User-friendly! –1
Voltage free! – Automatically applicable from 100V-240V. Just plug in. It’s ready to use!
User-friendly! – 2
Intuitively operation control panel for various settings.
Ø Simple operation to set tensions, modes, etc.
Ø 8 different tensions can be set in one style, and 50 different styles can be stored and easily paged.
Ø Marriage of different styles is possible in case more different tensions needed for 1 style – Maximum 400 tensions can be set!
Ø Copy-Paste of style is available for quicker setting of similar styles.
Ø “Teaching mode” is available (in case of automatic process change) for practical setting of tension and process changing points.
User-friendly! – 3
“Seamless setting from highest to lowest tension and difference in kinds of tape
Other brand device has independent “sensitivity control” for operator to do fine adjustment of sensor’s sensitivity – in case of big change in tape tension and type of tape, continuous vibration of roller may happen as the sensor detects tension change and roller tries to adjust feeding amount too much frequently. However, with Yamato ACCU-10, users do not required to do it as the device automatically makes sensitivity adjustment.
User-friendly! – 4
Ply (joint) detector is included as standard function. The device detects ply (joint) of tape passing through rollers, then inform operator by beep sound to prevent him/her from making defective work,
User-friendly! – 5
7-segment process display and “count-down indicator (in case of automatic process change)” informs current process and approach of process changing point without forcing operators to turn their head.
Usually, garments require tape attaching have lot of curves in its cutting pattern and correct shape and size is strictly required. In this case, operator should concentrate on fabric handling while watching fabric-trimming position, for even cutting margin to achieve accurate finish in shape. However, control panel of similar devices are usually fixed on the table top in the right-hand side of operator and it forces operator to have a glance at the panel from time to time to check whether she/he is sewing with proper tape feeding amount and disturbs concentration on handling.
On the other hand, Yamato ACCU-10 has independent process display (included in any model as standard accessory) to be fixed near to needle drop point to allow operator to check current process while concentrating on fabric cutting margin. Also, in case of automatic process (tension) change using stitch count, 5 (five) independent LEDs, which are set right beside the process display, light and brink as preset stitch numbers are counted, and inform operator approach of process changing point.
|
Process display and “count down indicator” of ACCU-10 |
|
|
Versatile! －１
Can be set on table in many ways to feed tape from top, bottom and side of machine. Besides, for convenience at each setting position, rotating direction of untangling wheel can be switched. Plus, “Clamp Style” is introduced for setting both tape feeder unit and control box on machine table, for higher mobility of the device from machine to machine, according to your production layout.
Versatile!-2
Can also be used as “tension free tape dispenser” (Like our AEF ) if you don’t have work requires tension tape feeding.
Versatile!-3
Can be used along with any kinds of sewing machine used for tape attaching operation to upgrade your product quality by the efficient use of your existing resources.
Expandable!
The device has capability to control various additional devices like tape cutter, chain cutter, thread tension release, waste suction, and automatic machine stop (in case of use with servo motor).
Below models are already established .
Ø For the use in combination with lace attaching interlock stitch M/C (i.e. VF2539-1-5-8)
Ø Tape to be supplied from top
Ø For the use in combination with lace attaching interlock stitch M/C (i.e. VF2539-1-5-8)
Ø Tape to be supplied from top
Ø Hall IC included for stitch count.
Ø For the use in combination with lace attaching interlock stitch M/C (i.e. VF2539-1-5-8)
Ø Tape to be supplied from top
Ø Hall IC + Magnet-embedded handwheel included for stitch counting.
Ø “Tension release switch” to be installed on foot lift chain is included, to be used along with clutch motor.
Ø For the use in combination with tape binding / lip binding interlock stitch M/C (i.e. VF2503-8)
Ø Tape to be supplied from side
Ø Hall IC included for stitch count.
Ø For the use in combination with tape binding / lip binding interlock stitch M/C (i.e. VF2503-8)
Ø Tape to be supplied from side
Ø Hall IC + Magnet-embedded handwheel included for stitch counting.
Ø For the use in combination with lockstitch zigzag M/C (i.e. LG2105-LW-4)
Ø Tape to be supplied from top
Ø “Tension release switch” to be installed on knee lever is included.
Ø For the use in combination with lockstitch zigzag M/C (i.e. LG2105-LW-4)
Ø Tape to be supplied from top
Ø Hall IC + Magnet-embedded handwheel included for stitch counting.
Ø “Tension release switch” to be installed on knee lever is included.
Below models are to be established shortly:
Ø For the use in combination with lace attaching interlock stitch M/C (i.e. VF2539-1-5-8)
Ø Tape to be supplied from top
Ø “Tension release switch” to be installed on foot lift chain is included, to be used along with clutch motor.
Ø For the use in combination with lace attaching interlock stitch M/C (i.e. VF2539-1-5-8)
Ø Tape to be supplied from top
Ø “Tension release switch” to be installed on pitman rod is included, to be used along with servo motor.
Ø For the use in combination with lace attaching interlock stitch M/C with “Yamato brand compact servo motor” (i.e. VF2539-1-5-8/Y)
Ø Tape to be supplied from top
Ø Connector cable to take rotation signal from Y motor is included.
|
Technical table Bold & Underlined shows the advantage points of ACCU10 |
|
|
YAMATO |
|
|
Model |
ACCU-10 |
|
Means for detecting tension |
Distortion Gauge Sensor |
|
Measurable tension range |
5 g – 700 g |
|
|
|
|
Roller width |
75mm |
|
Motor for driving roller |
DC Brushless |
|
Max. Tape Width |
72mm |
|
|
|
|
Untangling Wheel |
Standard |
|
Motor |
DC Brushless |
|
Turning direction |
Switchable |
|
Turning Speed |
Adjustable |
|
|
|
|
Process Indicator |
Standard |
|
Countdown Indicator |
Standard |
|
Finger Switch (*5) |
Option |
|
Knee switch |
Standard |
|
|
|
|
Ply (joint) detector |
Standard |
|
Free tension (AEF-like) mode |
Standard |
|
|
|
|
Processes / style |
8 |
|
Max. Styles stored |
50 |
|
Marriage of styles |
Standard |
|
Copy+Paste of styles |
Standard |
|
Teaching Mode |
Standard |
